Provide a name for this task.

Select a pre-configured MLLP server from the list.

Specify the file name and path for the file to be sent. A file name is required.

Specify the name of a variable of type File List that contains the files to send to the MLLP server, for example $(variableName).

The queue on the MLLP server that will hold the information. The following options are available:

Joblog: The synchronous response will be saved to the job log.
File: The synchronous response will be saved to the file specified in the Response File attribute.
Discard: The response will be discarded.

Specify the name of the file to which the response, if any, should be saved. This is required if the Destination attribute is set to File.

Select the action to take when the specified file already exists.

Default Value: rename

Specify if to fail the job if the acknowledgement type received for a message to the MLLP server is not Application Accept (AA) or Commit Accept (CA).

Default: Yes

Specify if to retry the job if the acknowledgement type received is Application Reject (AR) or Commit Reject (CR).

Default: No

Specify the number of message retry attempts where the response cannot be Application Accept (AA) or Application Error (AE) on the first attempt.

Default: 0

Specify the length of time in seconds between message retry attempts.

Default: 0

Specify the name of the variable that will contain an MLLP server response for the variable.

Use these options to configure the connection properties to an MLLP Server. If using an MLLP Server resource, these attributes can be used to override properties defined in the resource.

Host

Specify the host name or IP address of the MLLP Server. This is needed if an MLLP resource was not specified or to override the host name specified for the MLLP resource.

Port

Specify the port number to connect to.

Default: 2575

Response Timeout

Specify the maximum amount of time to wait in seconds from the moment the response from the MLLP server is received after sending the message. A timeout value of zero is interpreted as an infinite timeout.

Default: 30

Connection Timeout

Specify the maximum amount of time to wait in seconds to establish a connection to the MLLP server. A timeout value of zero is interpreted as an infinite timeout.

Default: 30

Connection Retry Attempts

Specify the number of times to retry the connection if not established on the first try.

Default: 0

Connection Retry Interval

Specify the number of seconds to wait between each retry attempt.

Default: 0

Specify the following options if MLLP connections from this server require the use of a proxy server. If there is direct access to the MLLP Server, leave these options blank.

Proxy Type

Select the type of proxy server you would like to use to connect to the target server. If left blank and a proxy host is specified, this value will default to a proxy type of HTTP.

Default: http

Host

Specify the host name or IP address of the proxy server. This is required if your system uses a proxy server to make HTTP/HTTPS connections.

Alternate Host

Specify an alternate host name or IP address of the proxy server.

Port

Specify the port number on which the proxy server is listening.

Default: 80

User

Specify the user name or login name if the proxy server requires authentication.

Password

Specify the password for the proxy server.

Is Password Encrypted?

Specify if the proxy server password is in encrypted form.

Specify the level of logging to use while executing this task. Valid options are - silent, normal, verbose and debug.

Default Value: Inherited from parent Module.

Specify a condition that must be satisfied before this task can be executed. This task will be skipped if the specified condition is not met.

Whether or not this task is disabled.

Default Value: false

Specify the action to take when this task errors out. Valid options are - abort, continue, call:[module] and setVariable:[name]=[value]. For call:[module] replace [module] with the name of the module in the project (e.g. call:ErrorModule). For setVariable:[name]=[value] replace [name] with a variable name and [value] with the variable value (e.g. setVariable:error=true).

Default Value: Inherited from parent Module